# Presets of this part (factory/PRESETS.md). Written by factory/gen.py.

[[presets]]
id = "M1.6-close-min"
title = "M1.6 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M1.6", fit = "close", tolerance = "min" }
aliases = ["M1.6 clearance hole close", "M1.6 close clearance hole", "M1.6 clearance hole", "ISO 273 M1.6 fine", "M1.6 close fit hole", "1.7 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M1.6-close-mean"
title = "M1.6 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M1.6", fit = "close", tolerance = "mean" }
aliases = ["M1.6 clearance hole close", "M1.6 close clearance hole", "M1.6 clearance hole", "ISO 273 M1.6 fine", "M1.6 close fit hole", "1.75 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M1.6-close-max"
title = "M1.6 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M1.6", fit = "close", tolerance = "max" }
aliases = ["M1.6 clearance hole close", "M1.6 close clearance hole", "M1.6 clearance hole", "ISO 273 M1.6 fine", "M1.6 close fit hole", "1.8 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M1.6-normal-min"
title = "M1.6 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M1.6", fit = "normal", tolerance = "min" }
aliases = ["M1.6 clearance hole normal", "M1.6 normal clearance hole", "M1.6 clearance hole", "ISO 273 M1.6 medium", "M1.6 normal fit hole", "1.8 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M1.6-normal-mean"
title = "M1.6 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M1.6", fit = "normal", tolerance = "mean" }
aliases = ["M1.6 clearance hole normal", "M1.6 normal clearance hole", "M1.6 clearance hole", "ISO 273 M1.6 medium", "M1.6 normal fit hole", "1.87 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M1.6-normal-max"
title = "M1.6 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M1.6", fit = "normal", tolerance = "max" }
aliases = ["M1.6 clearance hole normal", "M1.6 normal clearance hole", "M1.6 clearance hole", "ISO 273 M1.6 medium", "M1.6 normal fit hole", "1.94 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M1.6-loose-min"
title = "M1.6 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M1.6", fit = "loose", tolerance = "min" }
aliases = ["M1.6 clearance hole loose", "M1.6 loose clearance hole", "M1.6 clearance hole", "ISO 273 M1.6 coarse", "M1.6 loose fit hole", "2 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M1.6-loose-mean"
title = "M1.6 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M1.6", fit = "loose", tolerance = "mean" }
aliases = ["M1.6 clearance hole loose", "M1.6 loose clearance hole", "M1.6 clearance hole", "ISO 273 M1.6 coarse", "M1.6 loose fit hole", "2.125 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M1.6-loose-max"
title = "M1.6 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M1.6", fit = "loose", tolerance = "max" }
aliases = ["M1.6 clearance hole loose", "M1.6 loose clearance hole", "M1.6 clearance hole", "ISO 273 M1.6 coarse", "M1.6 loose fit hole", "2.25 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M2-close-min"
title = "M2 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M2", fit = "close", tolerance = "min" }
aliases = ["M2 clearance hole close", "M2 close clearance hole", "M2 clearance hole", "ISO 273 M2 fine", "M2 close fit hole", "2.2 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M2-close-mean"
title = "M2 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M2", fit = "close", tolerance = "mean" }
aliases = ["M2 clearance hole close", "M2 close clearance hole", "M2 clearance hole", "ISO 273 M2 fine", "M2 close fit hole", "2.25 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M2-close-max"
title = "M2 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M2", fit = "close", tolerance = "max" }
aliases = ["M2 clearance hole close", "M2 close clearance hole", "M2 clearance hole", "ISO 273 M2 fine", "M2 close fit hole", "2.3 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M2-normal-min"
title = "M2 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M2", fit = "normal", tolerance = "min" }
aliases = ["M2 clearance hole normal", "M2 normal clearance hole", "M2 clearance hole", "ISO 273 M2 medium", "M2 normal fit hole", "2.4 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M2-normal-mean"
title = "M2 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M2", fit = "normal", tolerance = "mean" }
aliases = ["M2 clearance hole normal", "M2 normal clearance hole", "M2 clearance hole", "ISO 273 M2 medium", "M2 normal fit hole", "2.47 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M2-normal-max"
title = "M2 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M2", fit = "normal", tolerance = "max" }
aliases = ["M2 clearance hole normal", "M2 normal clearance hole", "M2 clearance hole", "ISO 273 M2 medium", "M2 normal fit hole", "2.54 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M2-loose-min"
title = "M2 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M2", fit = "loose", tolerance = "min" }
aliases = ["M2 clearance hole loose", "M2 loose clearance hole", "M2 clearance hole", "ISO 273 M2 coarse", "M2 loose fit hole", "2.6 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M2-loose-mean"
title = "M2 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M2", fit = "loose", tolerance = "mean" }
aliases = ["M2 clearance hole loose", "M2 loose clearance hole", "M2 clearance hole", "ISO 273 M2 coarse", "M2 loose fit hole", "2.725 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M2-loose-max"
title = "M2 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M2", fit = "loose", tolerance = "max" }
aliases = ["M2 clearance hole loose", "M2 loose clearance hole", "M2 clearance hole", "ISO 273 M2 coarse", "M2 loose fit hole", "2.85 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M2.5-close-min"
title = "M2.5 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M2.5", fit = "close", tolerance = "min" }
aliases = ["M2.5 clearance hole close", "M2.5 close clearance hole", "M2.5 clearance hole", "ISO 273 M2.5 fine", "M2.5 close fit hole", "2.7 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M2.5-close-mean"
title = "M2.5 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M2.5", fit = "close", tolerance = "mean" }
aliases = ["M2.5 clearance hole close", "M2.5 close clearance hole", "M2.5 clearance hole", "ISO 273 M2.5 fine", "M2.5 close fit hole", "2.75 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M2.5-close-max"
title = "M2.5 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M2.5", fit = "close", tolerance = "max" }
aliases = ["M2.5 clearance hole close", "M2.5 close clearance hole", "M2.5 clearance hole", "ISO 273 M2.5 fine", "M2.5 close fit hole", "2.8 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M2.5-normal-min"
title = "M2.5 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M2.5", fit = "normal", tolerance = "min" }
aliases = ["M2.5 clearance hole normal", "M2.5 normal clearance hole", "M2.5 clearance hole", "ISO 273 M2.5 medium", "M2.5 normal fit hole", "2.9 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M2.5-normal-mean"
title = "M2.5 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M2.5", fit = "normal", tolerance = "mean" }
aliases = ["M2.5 clearance hole normal", "M2.5 normal clearance hole", "M2.5 clearance hole", "ISO 273 M2.5 medium", "M2.5 normal fit hole", "2.97 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M2.5-normal-max"
title = "M2.5 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M2.5", fit = "normal", tolerance = "max" }
aliases = ["M2.5 clearance hole normal", "M2.5 normal clearance hole", "M2.5 clearance hole", "ISO 273 M2.5 medium", "M2.5 normal fit hole", "3.04 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M2.5-loose-min"
title = "M2.5 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M2.5", fit = "loose", tolerance = "min" }
aliases = ["M2.5 clearance hole loose", "M2.5 loose clearance hole", "M2.5 clearance hole", "ISO 273 M2.5 coarse", "M2.5 loose fit hole", "3.1 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M2.5-loose-mean"
title = "M2.5 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M2.5", fit = "loose", tolerance = "mean" }
aliases = ["M2.5 clearance hole loose", "M2.5 loose clearance hole", "M2.5 clearance hole", "ISO 273 M2.5 coarse", "M2.5 loose fit hole", "3.25 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M2.5-loose-max"
title = "M2.5 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M2.5", fit = "loose", tolerance = "max" }
aliases = ["M2.5 clearance hole loose", "M2.5 loose clearance hole", "M2.5 clearance hole", "ISO 273 M2.5 coarse", "M2.5 loose fit hole", "3.4 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M3-close-min"
title = "M3 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M3", fit = "close", tolerance = "min" }
aliases = ["M3 clearance hole close", "M3 close clearance hole", "M3 clearance hole", "ISO 273 M3 fine", "M3 close fit hole", "3.2 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M3-close-mean"
title = "M3 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M3", fit = "close", tolerance = "mean" }
aliases = ["M3 clearance hole close", "M3 close clearance hole", "M3 clearance hole", "ISO 273 M3 fine", "M3 close fit hole", "3.26 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M3-close-max"
title = "M3 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M3", fit = "close", tolerance = "max" }
aliases = ["M3 clearance hole close", "M3 close clearance hole", "M3 clearance hole", "ISO 273 M3 fine", "M3 close fit hole", "3.32 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M3-normal-min"
title = "M3 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M3", fit = "normal", tolerance = "min" }
aliases = ["M3 clearance hole normal", "M3 normal clearance hole", "M3 clearance hole", "ISO 273 M3 medium", "M3 normal fit hole", "3.4 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M3-normal-mean"
title = "M3 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M3", fit = "normal", tolerance = "mean" }
aliases = ["M3 clearance hole normal", "M3 normal clearance hole", "M3 clearance hole", "ISO 273 M3 medium", "M3 normal fit hole", "3.49 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M3-normal-max"
title = "M3 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M3", fit = "normal", tolerance = "max" }
aliases = ["M3 clearance hole normal", "M3 normal clearance hole", "M3 clearance hole", "ISO 273 M3 medium", "M3 normal fit hole", "3.58 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M3-loose-min"
title = "M3 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M3", fit = "loose", tolerance = "min" }
aliases = ["M3 clearance hole loose", "M3 loose clearance hole", "M3 clearance hole", "ISO 273 M3 coarse", "M3 loose fit hole", "3.6 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M3-loose-mean"
title = "M3 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M3", fit = "loose", tolerance = "mean" }
aliases = ["M3 clearance hole loose", "M3 loose clearance hole", "M3 clearance hole", "ISO 273 M3 coarse", "M3 loose fit hole", "3.75 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M3-loose-max"
title = "M3 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M3", fit = "loose", tolerance = "max" }
aliases = ["M3 clearance hole loose", "M3 loose clearance hole", "M3 clearance hole", "ISO 273 M3 coarse", "M3 loose fit hole", "3.9 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M4-close-min"
title = "M4 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M4", fit = "close", tolerance = "min" }
aliases = ["M4 clearance hole close", "M4 close clearance hole", "M4 clearance hole", "ISO 273 M4 fine", "M4 close fit hole", "4.3 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M4-close-mean"
title = "M4 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M4", fit = "close", tolerance = "mean" }
aliases = ["M4 clearance hole close", "M4 close clearance hole", "M4 clearance hole", "ISO 273 M4 fine", "M4 close fit hole", "4.36 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M4-close-max"
title = "M4 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M4", fit = "close", tolerance = "max" }
aliases = ["M4 clearance hole close", "M4 close clearance hole", "M4 clearance hole", "ISO 273 M4 fine", "M4 close fit hole", "4.42 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M4-normal-min"
title = "M4 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M4", fit = "normal", tolerance = "min" }
aliases = ["M4 clearance hole normal", "M4 normal clearance hole", "M4 clearance hole", "ISO 273 M4 medium", "M4 normal fit hole", "4.5 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M4-normal-mean"
title = "M4 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M4", fit = "normal", tolerance = "mean" }
aliases = ["M4 clearance hole normal", "M4 normal clearance hole", "M4 clearance hole", "ISO 273 M4 medium", "M4 normal fit hole", "4.59 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M4-normal-max"
title = "M4 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M4", fit = "normal", tolerance = "max" }
aliases = ["M4 clearance hole normal", "M4 normal clearance hole", "M4 clearance hole", "ISO 273 M4 medium", "M4 normal fit hole", "4.68 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M4-loose-min"
title = "M4 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M4", fit = "loose", tolerance = "min" }
aliases = ["M4 clearance hole loose", "M4 loose clearance hole", "M4 clearance hole", "ISO 273 M4 coarse", "M4 loose fit hole", "4.8 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M4-loose-mean"
title = "M4 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M4", fit = "loose", tolerance = "mean" }
aliases = ["M4 clearance hole loose", "M4 loose clearance hole", "M4 clearance hole", "ISO 273 M4 coarse", "M4 loose fit hole", "4.95 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M4-loose-max"
title = "M4 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M4", fit = "loose", tolerance = "max" }
aliases = ["M4 clearance hole loose", "M4 loose clearance hole", "M4 clearance hole", "ISO 273 M4 coarse", "M4 loose fit hole", "5.1 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M5-close-min"
title = "M5 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M5", fit = "close", tolerance = "min" }
aliases = ["M5 clearance hole close", "M5 close clearance hole", "M5 clearance hole", "ISO 273 M5 fine", "M5 close fit hole", "5.3 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M5-close-mean"
title = "M5 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M5", fit = "close", tolerance = "mean" }
aliases = ["M5 clearance hole close", "M5 close clearance hole", "M5 clearance hole", "ISO 273 M5 fine", "M5 close fit hole", "5.36 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M5-close-max"
title = "M5 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M5", fit = "close", tolerance = "max" }
aliases = ["M5 clearance hole close", "M5 close clearance hole", "M5 clearance hole", "ISO 273 M5 fine", "M5 close fit hole", "5.42 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M5-normal-min"
title = "M5 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M5", fit = "normal", tolerance = "min" }
aliases = ["M5 clearance hole normal", "M5 normal clearance hole", "M5 clearance hole", "ISO 273 M5 medium", "M5 normal fit hole", "5.5 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M5-normal-mean"
title = "M5 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M5", fit = "normal", tolerance = "mean" }
aliases = ["M5 clearance hole normal", "M5 normal clearance hole", "M5 clearance hole", "ISO 273 M5 medium", "M5 normal fit hole", "5.59 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M5-normal-max"
title = "M5 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M5", fit = "normal", tolerance = "max" }
aliases = ["M5 clearance hole normal", "M5 normal clearance hole", "M5 clearance hole", "ISO 273 M5 medium", "M5 normal fit hole", "5.68 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M5-loose-min"
title = "M5 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M5", fit = "loose", tolerance = "min" }
aliases = ["M5 clearance hole loose", "M5 loose clearance hole", "M5 clearance hole", "ISO 273 M5 coarse", "M5 loose fit hole", "5.8 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M5-loose-mean"
title = "M5 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M5", fit = "loose", tolerance = "mean" }
aliases = ["M5 clearance hole loose", "M5 loose clearance hole", "M5 clearance hole", "ISO 273 M5 coarse", "M5 loose fit hole", "5.95 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M5-loose-max"
title = "M5 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M5", fit = "loose", tolerance = "max" }
aliases = ["M5 clearance hole loose", "M5 loose clearance hole", "M5 clearance hole", "ISO 273 M5 coarse", "M5 loose fit hole", "6.1 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M6-close-min"
title = "M6 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M6", fit = "close", tolerance = "min" }
aliases = ["M6 clearance hole close", "M6 close clearance hole", "M6 clearance hole", "ISO 273 M6 fine", "M6 close fit hole", "6.4 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M6-close-mean"
title = "M6 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M6", fit = "close", tolerance = "mean" }
aliases = ["M6 clearance hole close", "M6 close clearance hole", "M6 clearance hole", "ISO 273 M6 fine", "M6 close fit hole", "6.475 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M6-close-max"
title = "M6 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M6", fit = "close", tolerance = "max" }
aliases = ["M6 clearance hole close", "M6 close clearance hole", "M6 clearance hole", "ISO 273 M6 fine", "M6 close fit hole", "6.55 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M6-normal-min"
title = "M6 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M6", fit = "normal", tolerance = "min" }
aliases = ["M6 clearance hole normal", "M6 normal clearance hole", "M6 clearance hole", "ISO 273 M6 medium", "M6 normal fit hole", "6.6 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M6-normal-mean"
title = "M6 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M6", fit = "normal", tolerance = "mean" }
aliases = ["M6 clearance hole normal", "M6 normal clearance hole", "M6 clearance hole", "ISO 273 M6 medium", "M6 normal fit hole", "6.71 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M6-normal-max"
title = "M6 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M6", fit = "normal", tolerance = "max" }
aliases = ["M6 clearance hole normal", "M6 normal clearance hole", "M6 clearance hole", "ISO 273 M6 medium", "M6 normal fit hole", "6.82 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M6-loose-min"
title = "M6 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M6", fit = "loose", tolerance = "min" }
aliases = ["M6 clearance hole loose", "M6 loose clearance hole", "M6 clearance hole", "ISO 273 M6 coarse", "M6 loose fit hole", "7 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M6-loose-mean"
title = "M6 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M6", fit = "loose", tolerance = "mean" }
aliases = ["M6 clearance hole loose", "M6 loose clearance hole", "M6 clearance hole", "ISO 273 M6 coarse", "M6 loose fit hole", "7.18 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M6-loose-max"
title = "M6 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M6", fit = "loose", tolerance = "max" }
aliases = ["M6 clearance hole loose", "M6 loose clearance hole", "M6 clearance hole", "ISO 273 M6 coarse", "M6 loose fit hole", "7.36 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M8-close-min"
title = "M8 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M8", fit = "close", tolerance = "min" }
aliases = ["M8 clearance hole close", "M8 close clearance hole", "M8 clearance hole", "ISO 273 M8 fine", "M8 close fit hole", "8.4 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M8-close-mean"
title = "M8 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M8", fit = "close", tolerance = "mean" }
aliases = ["M8 clearance hole close", "M8 close clearance hole", "M8 clearance hole", "ISO 273 M8 fine", "M8 close fit hole", "8.475 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M8-close-max"
title = "M8 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M8", fit = "close", tolerance = "max" }
aliases = ["M8 clearance hole close", "M8 close clearance hole", "M8 clearance hole", "ISO 273 M8 fine", "M8 close fit hole", "8.55 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M8-normal-min"
title = "M8 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M8", fit = "normal", tolerance = "min" }
aliases = ["M8 clearance hole normal", "M8 normal clearance hole", "M8 clearance hole", "ISO 273 M8 medium", "M8 normal fit hole", "9 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M8-normal-mean"
title = "M8 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M8", fit = "normal", tolerance = "mean" }
aliases = ["M8 clearance hole normal", "M8 normal clearance hole", "M8 clearance hole", "ISO 273 M8 medium", "M8 normal fit hole", "9.11 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M8-normal-max"
title = "M8 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M8", fit = "normal", tolerance = "max" }
aliases = ["M8 clearance hole normal", "M8 normal clearance hole", "M8 clearance hole", "ISO 273 M8 medium", "M8 normal fit hole", "9.22 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M8-loose-min"
title = "M8 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M8", fit = "loose", tolerance = "min" }
aliases = ["M8 clearance hole loose", "M8 loose clearance hole", "M8 clearance hole", "ISO 273 M8 coarse", "M8 loose fit hole", "10 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M8-loose-mean"
title = "M8 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M8", fit = "loose", tolerance = "mean" }
aliases = ["M8 clearance hole loose", "M8 loose clearance hole", "M8 clearance hole", "ISO 273 M8 coarse", "M8 loose fit hole", "10.18 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M8-loose-max"
title = "M8 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M8", fit = "loose", tolerance = "max" }
aliases = ["M8 clearance hole loose", "M8 loose clearance hole", "M8 clearance hole", "ISO 273 M8 coarse", "M8 loose fit hole", "10.36 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M10-close-min"
title = "M10 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M10", fit = "close", tolerance = "min" }
aliases = ["M10 clearance hole close", "M10 close clearance hole", "M10 clearance hole", "ISO 273 M10 fine", "M10 close fit hole", "10.5 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M10-close-mean"
title = "M10 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M10", fit = "close", tolerance = "mean" }
aliases = ["M10 clearance hole close", "M10 close clearance hole", "M10 clearance hole", "ISO 273 M10 fine", "M10 close fit hole", "10.59 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M10-close-max"
title = "M10 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M10", fit = "close", tolerance = "max" }
aliases = ["M10 clearance hole close", "M10 close clearance hole", "M10 clearance hole", "ISO 273 M10 fine", "M10 close fit hole", "10.68 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M10-normal-min"
title = "M10 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M10", fit = "normal", tolerance = "min" }
aliases = ["M10 clearance hole normal", "M10 normal clearance hole", "M10 clearance hole", "ISO 273 M10 medium", "M10 normal fit hole", "11 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M10-normal-mean"
title = "M10 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M10", fit = "normal", tolerance = "mean" }
aliases = ["M10 clearance hole normal", "M10 normal clearance hole", "M10 clearance hole", "ISO 273 M10 medium", "M10 normal fit hole", "11.135 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M10-normal-max"
title = "M10 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M10", fit = "normal", tolerance = "max" }
aliases = ["M10 clearance hole normal", "M10 normal clearance hole", "M10 clearance hole", "ISO 273 M10 medium", "M10 normal fit hole", "11.27 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M10-loose-min"
title = "M10 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M10", fit = "loose", tolerance = "min" }
aliases = ["M10 clearance hole loose", "M10 loose clearance hole", "M10 clearance hole", "ISO 273 M10 coarse", "M10 loose fit hole", "12 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M10-loose-mean"
title = "M10 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M10", fit = "loose", tolerance = "mean" }
aliases = ["M10 clearance hole loose", "M10 loose clearance hole", "M10 clearance hole", "ISO 273 M10 coarse", "M10 loose fit hole", "12.215 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M10-loose-max"
title = "M10 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M10", fit = "loose", tolerance = "max" }
aliases = ["M10 clearance hole loose", "M10 loose clearance hole", "M10 clearance hole", "ISO 273 M10 coarse", "M10 loose fit hole", "12.43 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M12-close-min"
title = "M12 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M12", fit = "close", tolerance = "min" }
aliases = ["M12 clearance hole close", "M12 close clearance hole", "M12 clearance hole", "ISO 273 M12 fine", "M12 close fit hole", "13 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M12-close-mean"
title = "M12 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M12", fit = "close", tolerance = "mean" }
aliases = ["M12 clearance hole close", "M12 close clearance hole", "M12 clearance hole", "ISO 273 M12 fine", "M12 close fit hole", "13.09 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M12-close-max"
title = "M12 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M12", fit = "close", tolerance = "max" }
aliases = ["M12 clearance hole close", "M12 close clearance hole", "M12 clearance hole", "ISO 273 M12 fine", "M12 close fit hole", "13.18 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M12-normal-min"
title = "M12 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M12", fit = "normal", tolerance = "min" }
aliases = ["M12 clearance hole normal", "M12 normal clearance hole", "M12 clearance hole", "ISO 273 M12 medium", "M12 normal fit hole", "13.5 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M12-normal-mean"
title = "M12 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M12", fit = "normal", tolerance = "mean" }
aliases = ["M12 clearance hole normal", "M12 normal clearance hole", "M12 clearance hole", "ISO 273 M12 medium", "M12 normal fit hole", "13.635 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M12-normal-max"
title = "M12 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M12", fit = "normal", tolerance = "max" }
aliases = ["M12 clearance hole normal", "M12 normal clearance hole", "M12 clearance hole", "ISO 273 M12 medium", "M12 normal fit hole", "13.77 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M12-loose-min"
title = "M12 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M12", fit = "loose", tolerance = "min" }
aliases = ["M12 clearance hole loose", "M12 loose clearance hole", "M12 clearance hole", "ISO 273 M12 coarse", "M12 loose fit hole", "14.5 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M12-loose-mean"
title = "M12 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M12", fit = "loose", tolerance = "mean" }
aliases = ["M12 clearance hole loose", "M12 loose clearance hole", "M12 clearance hole", "ISO 273 M12 coarse", "M12 loose fit hole", "14.715 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M12-loose-max"
title = "M12 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M12", fit = "loose", tolerance = "max" }
aliases = ["M12 clearance hole loose", "M12 loose clearance hole", "M12 clearance hole", "ISO 273 M12 coarse", "M12 loose fit hole", "14.93 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M14-close-min"
title = "M14 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M14", fit = "close", tolerance = "min" }
aliases = ["M14 clearance hole close", "M14 close clearance hole", "M14 clearance hole", "ISO 273 M14 fine", "M14 close fit hole", "15 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M14-close-mean"
title = "M14 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M14", fit = "close", tolerance = "mean" }
aliases = ["M14 clearance hole close", "M14 close clearance hole", "M14 clearance hole", "ISO 273 M14 fine", "M14 close fit hole", "15.09 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M14-close-max"
title = "M14 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M14", fit = "close", tolerance = "max" }
aliases = ["M14 clearance hole close", "M14 close clearance hole", "M14 clearance hole", "ISO 273 M14 fine", "M14 close fit hole", "15.18 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M14-normal-min"
title = "M14 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M14", fit = "normal", tolerance = "min" }
aliases = ["M14 clearance hole normal", "M14 normal clearance hole", "M14 clearance hole", "ISO 273 M14 medium", "M14 normal fit hole", "15.5 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M14-normal-mean"
title = "M14 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M14", fit = "normal", tolerance = "mean" }
aliases = ["M14 clearance hole normal", "M14 normal clearance hole", "M14 clearance hole", "ISO 273 M14 medium", "M14 normal fit hole", "15.635 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M14-normal-max"
title = "M14 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M14", fit = "normal", tolerance = "max" }
aliases = ["M14 clearance hole normal", "M14 normal clearance hole", "M14 clearance hole", "ISO 273 M14 medium", "M14 normal fit hole", "15.77 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M14-loose-min"
title = "M14 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M14", fit = "loose", tolerance = "min" }
aliases = ["M14 clearance hole loose", "M14 loose clearance hole", "M14 clearance hole", "ISO 273 M14 coarse", "M14 loose fit hole", "16.5 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M14-loose-mean"
title = "M14 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M14", fit = "loose", tolerance = "mean" }
aliases = ["M14 clearance hole loose", "M14 loose clearance hole", "M14 clearance hole", "ISO 273 M14 coarse", "M14 loose fit hole", "16.715 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M14-loose-max"
title = "M14 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M14", fit = "loose", tolerance = "max" }
aliases = ["M14 clearance hole loose", "M14 loose clearance hole", "M14 clearance hole", "ISO 273 M14 coarse", "M14 loose fit hole", "16.93 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M16-close-min"
title = "M16 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M16", fit = "close", tolerance = "min" }
aliases = ["M16 clearance hole close", "M16 close clearance hole", "M16 clearance hole", "ISO 273 M16 fine", "M16 close fit hole", "17 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M16-close-mean"
title = "M16 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M16", fit = "close", tolerance = "mean" }
aliases = ["M16 clearance hole close", "M16 close clearance hole", "M16 clearance hole", "ISO 273 M16 fine", "M16 close fit hole", "17.09 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M16-close-max"
title = "M16 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M16", fit = "close", tolerance = "max" }
aliases = ["M16 clearance hole close", "M16 close clearance hole", "M16 clearance hole", "ISO 273 M16 fine", "M16 close fit hole", "17.18 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M16-normal-min"
title = "M16 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M16", fit = "normal", tolerance = "min" }
aliases = ["M16 clearance hole normal", "M16 normal clearance hole", "M16 clearance hole", "ISO 273 M16 medium", "M16 normal fit hole", "17.5 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M16-normal-mean"
title = "M16 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M16", fit = "normal", tolerance = "mean" }
aliases = ["M16 clearance hole normal", "M16 normal clearance hole", "M16 clearance hole", "ISO 273 M16 medium", "M16 normal fit hole", "17.635 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M16-normal-max"
title = "M16 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M16", fit = "normal", tolerance = "max" }
aliases = ["M16 clearance hole normal", "M16 normal clearance hole", "M16 clearance hole", "ISO 273 M16 medium", "M16 normal fit hole", "17.77 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M16-loose-min"
title = "M16 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M16", fit = "loose", tolerance = "min" }
aliases = ["M16 clearance hole loose", "M16 loose clearance hole", "M16 clearance hole", "ISO 273 M16 coarse", "M16 loose fit hole", "18.5 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M16-loose-mean"
title = "M16 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M16", fit = "loose", tolerance = "mean" }
aliases = ["M16 clearance hole loose", "M16 loose clearance hole", "M16 clearance hole", "ISO 273 M16 coarse", "M16 loose fit hole", "18.76 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M16-loose-max"
title = "M16 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M16", fit = "loose", tolerance = "max" }
aliases = ["M16 clearance hole loose", "M16 loose clearance hole", "M16 clearance hole", "ISO 273 M16 coarse", "M16 loose fit hole", "19.02 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M20-close-min"
title = "M20 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M20", fit = "close", tolerance = "min" }
aliases = ["M20 clearance hole close", "M20 close clearance hole", "M20 clearance hole", "ISO 273 M20 fine", "M20 close fit hole", "21 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M20-close-mean"
title = "M20 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M20", fit = "close", tolerance = "mean" }
aliases = ["M20 clearance hole close", "M20 close clearance hole", "M20 clearance hole", "ISO 273 M20 fine", "M20 close fit hole", "21.105 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M20-close-max"
title = "M20 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M20", fit = "close", tolerance = "max" }
aliases = ["M20 clearance hole close", "M20 close clearance hole", "M20 clearance hole", "ISO 273 M20 fine", "M20 close fit hole", "21.21 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M20-normal-min"
title = "M20 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M20", fit = "normal", tolerance = "min" }
aliases = ["M20 clearance hole normal", "M20 normal clearance hole", "M20 clearance hole", "ISO 273 M20 medium", "M20 normal fit hole", "22 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M20-normal-mean"
title = "M20 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M20", fit = "normal", tolerance = "mean" }
aliases = ["M20 clearance hole normal", "M20 normal clearance hole", "M20 clearance hole", "ISO 273 M20 medium", "M20 normal fit hole", "22.165 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M20-normal-max"
title = "M20 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M20", fit = "normal", tolerance = "max" }
aliases = ["M20 clearance hole normal", "M20 normal clearance hole", "M20 clearance hole", "ISO 273 M20 medium", "M20 normal fit hole", "22.33 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M20-loose-min"
title = "M20 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M20", fit = "loose", tolerance = "min" }
aliases = ["M20 clearance hole loose", "M20 loose clearance hole", "M20 clearance hole", "ISO 273 M20 coarse", "M20 loose fit hole", "24 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M20-loose-mean"
title = "M20 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M20", fit = "loose", tolerance = "mean" }
aliases = ["M20 clearance hole loose", "M20 loose clearance hole", "M20 clearance hole", "ISO 273 M20 coarse", "M20 loose fit hole", "24.26 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M20-loose-max"
title = "M20 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M20", fit = "loose", tolerance = "max" }
aliases = ["M20 clearance hole loose", "M20 loose clearance hole", "M20 clearance hole", "ISO 273 M20 coarse", "M20 loose fit hole", "24.52 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M24-close-min"
title = "M24 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M24", fit = "close", tolerance = "min" }
aliases = ["M24 clearance hole close", "M24 close clearance hole", "M24 clearance hole", "ISO 273 M24 fine", "M24 close fit hole", "25 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M24-close-mean"
title = "M24 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M24", fit = "close", tolerance = "mean" }
aliases = ["M24 clearance hole close", "M24 close clearance hole", "M24 clearance hole", "ISO 273 M24 fine", "M24 close fit hole", "25.105 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M24-close-max"
title = "M24 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M24", fit = "close", tolerance = "max" }
aliases = ["M24 clearance hole close", "M24 close clearance hole", "M24 clearance hole", "ISO 273 M24 fine", "M24 close fit hole", "25.21 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M24-normal-min"
title = "M24 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M24", fit = "normal", tolerance = "min" }
aliases = ["M24 clearance hole normal", "M24 normal clearance hole", "M24 clearance hole", "ISO 273 M24 medium", "M24 normal fit hole", "26 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M24-normal-mean"
title = "M24 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M24", fit = "normal", tolerance = "mean" }
aliases = ["M24 clearance hole normal", "M24 normal clearance hole", "M24 clearance hole", "ISO 273 M24 medium", "M24 normal fit hole", "26.165 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M24-normal-max"
title = "M24 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M24", fit = "normal", tolerance = "max" }
aliases = ["M24 clearance hole normal", "M24 normal clearance hole", "M24 clearance hole", "ISO 273 M24 medium", "M24 normal fit hole", "26.33 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M24-loose-min"
title = "M24 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M24", fit = "loose", tolerance = "min" }
aliases = ["M24 clearance hole loose", "M24 loose clearance hole", "M24 clearance hole", "ISO 273 M24 coarse", "M24 loose fit hole", "28 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M24-loose-mean"
title = "M24 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M24", fit = "loose", tolerance = "mean" }
aliases = ["M24 clearance hole loose", "M24 loose clearance hole", "M24 clearance hole", "ISO 273 M24 coarse", "M24 loose fit hole", "28.26 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M24-loose-max"
title = "M24 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M24", fit = "loose", tolerance = "max" }
aliases = ["M24 clearance hole loose", "M24 loose clearance hole", "M24 clearance hole", "ISO 273 M24 coarse", "M24 loose fit hole", "28.52 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M30-close-min"
title = "M30 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M30", fit = "close", tolerance = "min" }
aliases = ["M30 clearance hole close", "M30 close clearance hole", "M30 clearance hole", "ISO 273 M30 fine", "M30 close fit hole", "31 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M30-close-mean"
title = "M30 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M30", fit = "close", tolerance = "mean" }
aliases = ["M30 clearance hole close", "M30 close clearance hole", "M30 clearance hole", "ISO 273 M30 fine", "M30 close fit hole", "31.125 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M30-close-max"
title = "M30 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M30", fit = "close", tolerance = "max" }
aliases = ["M30 clearance hole close", "M30 close clearance hole", "M30 clearance hole", "ISO 273 M30 fine", "M30 close fit hole", "31.25 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M30-normal-min"
title = "M30 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M30", fit = "normal", tolerance = "min" }
aliases = ["M30 clearance hole normal", "M30 normal clearance hole", "M30 clearance hole", "ISO 273 M30 medium", "M30 normal fit hole", "33 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M30-normal-mean"
title = "M30 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M30", fit = "normal", tolerance = "mean" }
aliases = ["M30 clearance hole normal", "M30 normal clearance hole", "M30 clearance hole", "ISO 273 M30 medium", "M30 normal fit hole", "33.195 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M30-normal-max"
title = "M30 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M30", fit = "normal", tolerance = "max" }
aliases = ["M30 clearance hole normal", "M30 normal clearance hole", "M30 clearance hole", "ISO 273 M30 medium", "M30 normal fit hole", "33.39 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M30-loose-min"
title = "M30 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M30", fit = "loose", tolerance = "min" }
aliases = ["M30 clearance hole loose", "M30 loose clearance hole", "M30 clearance hole", "ISO 273 M30 coarse", "M30 loose fit hole", "35 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M30-loose-mean"
title = "M30 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M30", fit = "loose", tolerance = "mean" }
aliases = ["M30 clearance hole loose", "M30 loose clearance hole", "M30 clearance hole", "ISO 273 M30 coarse", "M30 loose fit hole", "35.31 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M30-loose-max"
title = "M30 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M30", fit = "loose", tolerance = "max" }
aliases = ["M30 clearance hole loose", "M30 loose clearance hole", "M30 clearance hole", "ISO 273 M30 coarse", "M30 loose fit hole", "35.62 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M36-close-min"
title = "M36 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M36", fit = "close", tolerance = "min" }
aliases = ["M36 clearance hole close", "M36 close clearance hole", "M36 clearance hole", "ISO 273 M36 fine", "M36 close fit hole", "37 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M36-close-mean"
title = "M36 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M36", fit = "close", tolerance = "mean" }
aliases = ["M36 clearance hole close", "M36 close clearance hole", "M36 clearance hole", "ISO 273 M36 fine", "M36 close fit hole", "37.125 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M36-close-max"
title = "M36 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M36", fit = "close", tolerance = "max" }
aliases = ["M36 clearance hole close", "M36 close clearance hole", "M36 clearance hole", "ISO 273 M36 fine", "M36 close fit hole", "37.25 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M36-normal-min"
title = "M36 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M36", fit = "normal", tolerance = "min" }
aliases = ["M36 clearance hole normal", "M36 normal clearance hole", "M36 clearance hole", "ISO 273 M36 medium", "M36 normal fit hole", "39 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M36-normal-mean"
title = "M36 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M36", fit = "normal", tolerance = "mean" }
aliases = ["M36 clearance hole normal", "M36 normal clearance hole", "M36 clearance hole", "ISO 273 M36 medium", "M36 normal fit hole", "39.195 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M36-normal-max"
title = "M36 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M36", fit = "normal", tolerance = "max" }
aliases = ["M36 clearance hole normal", "M36 normal clearance hole", "M36 clearance hole", "ISO 273 M36 medium", "M36 normal fit hole", "39.39 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M36-loose-min"
title = "M36 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M36", fit = "loose", tolerance = "min" }
aliases = ["M36 clearance hole loose", "M36 loose clearance hole", "M36 clearance hole", "ISO 273 M36 coarse", "M36 loose fit hole", "42 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M36-loose-mean"
title = "M36 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M36", fit = "loose", tolerance = "mean" }
aliases = ["M36 clearance hole loose", "M36 loose clearance hole", "M36 clearance hole", "ISO 273 M36 coarse", "M36 loose fit hole", "42.31 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M36-loose-max"
title = "M36 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M36", fit = "loose", tolerance = "max" }
aliases = ["M36 clearance hole loose", "M36 loose clearance hole", "M36 clearance hole", "ISO 273 M36 coarse", "M36 loose fit hole", "42.62 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M42-close-min"
title = "M42 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M42", fit = "close", tolerance = "min" }
aliases = ["M42 clearance hole close", "M42 close clearance hole", "M42 clearance hole", "ISO 273 M42 fine", "M42 close fit hole", "43 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M42-close-mean"
title = "M42 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M42", fit = "close", tolerance = "mean" }
aliases = ["M42 clearance hole close", "M42 close clearance hole", "M42 clearance hole", "ISO 273 M42 fine", "M42 close fit hole", "43.125 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M42-close-max"
title = "M42 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M42", fit = "close", tolerance = "max" }
aliases = ["M42 clearance hole close", "M42 close clearance hole", "M42 clearance hole", "ISO 273 M42 fine", "M42 close fit hole", "43.25 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M42-normal-min"
title = "M42 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M42", fit = "normal", tolerance = "min" }
aliases = ["M42 clearance hole normal", "M42 normal clearance hole", "M42 clearance hole", "ISO 273 M42 medium", "M42 normal fit hole", "45 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M42-normal-mean"
title = "M42 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M42", fit = "normal", tolerance = "mean" }
aliases = ["M42 clearance hole normal", "M42 normal clearance hole", "M42 clearance hole", "ISO 273 M42 medium", "M42 normal fit hole", "45.195 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M42-normal-max"
title = "M42 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M42", fit = "normal", tolerance = "max" }
aliases = ["M42 clearance hole normal", "M42 normal clearance hole", "M42 clearance hole", "ISO 273 M42 medium", "M42 normal fit hole", "45.39 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M42-loose-min"
title = "M42 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M42", fit = "loose", tolerance = "min" }
aliases = ["M42 clearance hole loose", "M42 loose clearance hole", "M42 clearance hole", "ISO 273 M42 coarse", "M42 loose fit hole", "48 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M42-loose-mean"
title = "M42 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M42", fit = "loose", tolerance = "mean" }
aliases = ["M42 clearance hole loose", "M42 loose clearance hole", "M42 clearance hole", "ISO 273 M42 coarse", "M42 loose fit hole", "48.31 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M42-loose-max"
title = "M42 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M42", fit = "loose", tolerance = "max" }
aliases = ["M42 clearance hole loose", "M42 loose clearance hole", "M42 clearance hole", "ISO 273 M42 coarse", "M42 loose fit hole", "48.62 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M48-close-min"
title = "M48 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M48", fit = "close", tolerance = "min" }
aliases = ["M48 clearance hole close", "M48 close clearance hole", "M48 clearance hole", "ISO 273 M48 fine", "M48 close fit hole", "50 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M48-close-mean"
title = "M48 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M48", fit = "close", tolerance = "mean" }
aliases = ["M48 clearance hole close", "M48 close clearance hole", "M48 clearance hole", "ISO 273 M48 fine", "M48 close fit hole", "50.125 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M48-close-max"
title = "M48 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M48", fit = "close", tolerance = "max" }
aliases = ["M48 clearance hole close", "M48 close clearance hole", "M48 clearance hole", "ISO 273 M48 fine", "M48 close fit hole", "50.25 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M48-normal-min"
title = "M48 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M48", fit = "normal", tolerance = "min" }
aliases = ["M48 clearance hole normal", "M48 normal clearance hole", "M48 clearance hole", "ISO 273 M48 medium", "M48 normal fit hole", "52 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M48-normal-mean"
title = "M48 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M48", fit = "normal", tolerance = "mean" }
aliases = ["M48 clearance hole normal", "M48 normal clearance hole", "M48 clearance hole", "ISO 273 M48 medium", "M48 normal fit hole", "52.23 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M48-normal-max"
title = "M48 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M48", fit = "normal", tolerance = "max" }
aliases = ["M48 clearance hole normal", "M48 normal clearance hole", "M48 clearance hole", "ISO 273 M48 medium", "M48 normal fit hole", "52.46 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M48-loose-min"
title = "M48 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M48", fit = "loose", tolerance = "min" }
aliases = ["M48 clearance hole loose", "M48 loose clearance hole", "M48 clearance hole", "ISO 273 M48 coarse", "M48 loose fit hole", "56 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M48-loose-mean"
title = "M48 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M48", fit = "loose", tolerance = "mean" }
aliases = ["M48 clearance hole loose", "M48 loose clearance hole", "M48 clearance hole", "ISO 273 M48 coarse", "M48 loose fit hole", "56.37 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M48-loose-max"
title = "M48 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M48", fit = "loose", tolerance = "max" }
aliases = ["M48 clearance hole loose", "M48 loose clearance hole", "M48 clearance hole", "ISO 273 M48 coarse", "M48 loose fit hole", "56.74 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M56-close-min"
title = "M56 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M56", fit = "close", tolerance = "min" }
aliases = ["M56 clearance hole close", "M56 close clearance hole", "M56 clearance hole", "ISO 273 M56 fine", "M56 close fit hole", "58 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M56-close-mean"
title = "M56 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M56", fit = "close", tolerance = "mean" }
aliases = ["M56 clearance hole close", "M56 close clearance hole", "M56 clearance hole", "ISO 273 M56 fine", "M56 close fit hole", "58.15 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M56-close-max"
title = "M56 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M56", fit = "close", tolerance = "max" }
aliases = ["M56 clearance hole close", "M56 close clearance hole", "M56 clearance hole", "ISO 273 M56 fine", "M56 close fit hole", "58.3 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M56-normal-min"
title = "M56 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M56", fit = "normal", tolerance = "min" }
aliases = ["M56 clearance hole normal", "M56 normal clearance hole", "M56 clearance hole", "ISO 273 M56 medium", "M56 normal fit hole", "62 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M56-normal-mean"
title = "M56 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M56", fit = "normal", tolerance = "mean" }
aliases = ["M56 clearance hole normal", "M56 normal clearance hole", "M56 clearance hole", "ISO 273 M56 medium", "M56 normal fit hole", "62.23 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M56-normal-max"
title = "M56 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M56", fit = "normal", tolerance = "max" }
aliases = ["M56 clearance hole normal", "M56 normal clearance hole", "M56 clearance hole", "ISO 273 M56 medium", "M56 normal fit hole", "62.46 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M56-loose-min"
title = "M56 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M56", fit = "loose", tolerance = "min" }
aliases = ["M56 clearance hole loose", "M56 loose clearance hole", "M56 clearance hole", "ISO 273 M56 coarse", "M56 loose fit hole", "66 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M56-loose-mean"
title = "M56 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M56", fit = "loose", tolerance = "mean" }
aliases = ["M56 clearance hole loose", "M56 loose clearance hole", "M56 clearance hole", "ISO 273 M56 coarse", "M56 loose fit hole", "66.37 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M56-loose-max"
title = "M56 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M56", fit = "loose", tolerance = "max" }
aliases = ["M56 clearance hole loose", "M56 loose clearance hole", "M56 clearance hole", "ISO 273 M56 coarse", "M56 loose fit hole", "66.74 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M64-close-min"
title = "M64 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M64", fit = "close", tolerance = "min" }
aliases = ["M64 clearance hole close", "M64 close clearance hole", "M64 clearance hole", "ISO 273 M64 fine", "M64 close fit hole", "66 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M64-close-mean"
title = "M64 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M64", fit = "close", tolerance = "mean" }
aliases = ["M64 clearance hole close", "M64 close clearance hole", "M64 clearance hole", "ISO 273 M64 fine", "M64 close fit hole", "66.15 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M64-close-max"
title = "M64 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M64", fit = "close", tolerance = "max" }
aliases = ["M64 clearance hole close", "M64 close clearance hole", "M64 clearance hole", "ISO 273 M64 fine", "M64 close fit hole", "66.3 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M64-normal-min"
title = "M64 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M64", fit = "normal", tolerance = "min" }
aliases = ["M64 clearance hole normal", "M64 normal clearance hole", "M64 clearance hole", "ISO 273 M64 medium", "M64 normal fit hole", "70 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M64-normal-mean"
title = "M64 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M64", fit = "normal", tolerance = "mean" }
aliases = ["M64 clearance hole normal", "M64 normal clearance hole", "M64 clearance hole", "ISO 273 M64 medium", "M64 normal fit hole", "70.23 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M64-normal-max"
title = "M64 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M64", fit = "normal", tolerance = "max" }
aliases = ["M64 clearance hole normal", "M64 normal clearance hole", "M64 clearance hole", "ISO 273 M64 medium", "M64 normal fit hole", "70.46 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M64-loose-min"
title = "M64 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M64", fit = "loose", tolerance = "min" }
aliases = ["M64 clearance hole loose", "M64 loose clearance hole", "M64 clearance hole", "ISO 273 M64 coarse", "M64 loose fit hole", "74 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M64-loose-mean"
title = "M64 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M64", fit = "loose", tolerance = "mean" }
aliases = ["M64 clearance hole loose", "M64 loose clearance hole", "M64 clearance hole", "ISO 273 M64 coarse", "M64 loose fit hole", "74.37 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M64-loose-max"
title = "M64 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M64", fit = "loose", tolerance = "max" }
aliases = ["M64 clearance hole loose", "M64 loose clearance hole", "M64 clearance hole", "ISO 273 M64 coarse", "M64 loose fit hole", "74.74 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M72-close-min"
title = "M72 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M72", fit = "close", tolerance = "min" }
aliases = ["M72 clearance hole close", "M72 close clearance hole", "M72 clearance hole", "ISO 273 M72 fine", "M72 close fit hole", "74 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M72-close-mean"
title = "M72 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M72", fit = "close", tolerance = "mean" }
aliases = ["M72 clearance hole close", "M72 close clearance hole", "M72 clearance hole", "ISO 273 M72 fine", "M72 close fit hole", "74.15 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M72-close-max"
title = "M72 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M72", fit = "close", tolerance = "max" }
aliases = ["M72 clearance hole close", "M72 close clearance hole", "M72 clearance hole", "ISO 273 M72 fine", "M72 close fit hole", "74.3 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M72-normal-min"
title = "M72 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M72", fit = "normal", tolerance = "min" }
aliases = ["M72 clearance hole normal", "M72 normal clearance hole", "M72 clearance hole", "ISO 273 M72 medium", "M72 normal fit hole", "78 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M72-normal-mean"
title = "M72 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M72", fit = "normal", tolerance = "mean" }
aliases = ["M72 clearance hole normal", "M72 normal clearance hole", "M72 clearance hole", "ISO 273 M72 medium", "M72 normal fit hole", "78.23 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M72-normal-max"
title = "M72 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M72", fit = "normal", tolerance = "max" }
aliases = ["M72 clearance hole normal", "M72 normal clearance hole", "M72 clearance hole", "ISO 273 M72 medium", "M72 normal fit hole", "78.46 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M72-loose-min"
title = "M72 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M72", fit = "loose", tolerance = "min" }
aliases = ["M72 clearance hole loose", "M72 loose clearance hole", "M72 clearance hole", "ISO 273 M72 coarse", "M72 loose fit hole", "82 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M72-loose-mean"
title = "M72 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M72", fit = "loose", tolerance = "mean" }
aliases = ["M72 clearance hole loose", "M72 loose clearance hole", "M72 clearance hole", "ISO 273 M72 coarse", "M72 loose fit hole", "82.435 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M72-loose-max"
title = "M72 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M72", fit = "loose", tolerance = "max" }
aliases = ["M72 clearance hole loose", "M72 loose clearance hole", "M72 clearance hole", "ISO 273 M72 coarse", "M72 loose fit hole", "82.87 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M80-close-min"
title = "M80 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M80", fit = "close", tolerance = "min" }
aliases = ["M80 clearance hole close", "M80 close clearance hole", "M80 clearance hole", "ISO 273 M80 fine", "M80 close fit hole", "82 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M80-close-mean"
title = "M80 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M80", fit = "close", tolerance = "mean" }
aliases = ["M80 clearance hole close", "M80 close clearance hole", "M80 clearance hole", "ISO 273 M80 fine", "M80 close fit hole", "82.175 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M80-close-max"
title = "M80 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M80", fit = "close", tolerance = "max" }
aliases = ["M80 clearance hole close", "M80 close clearance hole", "M80 clearance hole", "ISO 273 M80 fine", "M80 close fit hole", "82.35 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M80-normal-min"
title = "M80 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M80", fit = "normal", tolerance = "min" }
aliases = ["M80 clearance hole normal", "M80 normal clearance hole", "M80 clearance hole", "ISO 273 M80 medium", "M80 normal fit hole", "86 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M80-normal-mean"
title = "M80 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M80", fit = "normal", tolerance = "mean" }
aliases = ["M80 clearance hole normal", "M80 normal clearance hole", "M80 clearance hole", "ISO 273 M80 medium", "M80 normal fit hole", "86.27 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M80-normal-max"
title = "M80 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M80", fit = "normal", tolerance = "max" }
aliases = ["M80 clearance hole normal", "M80 normal clearance hole", "M80 clearance hole", "ISO 273 M80 medium", "M80 normal fit hole", "86.54 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M80-loose-min"
title = "M80 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M80", fit = "loose", tolerance = "min" }
aliases = ["M80 clearance hole loose", "M80 loose clearance hole", "M80 clearance hole", "ISO 273 M80 coarse", "M80 loose fit hole", "91 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M80-loose-mean"
title = "M80 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M80", fit = "loose", tolerance = "mean" }
aliases = ["M80 clearance hole loose", "M80 loose clearance hole", "M80 clearance hole", "ISO 273 M80 coarse", "M80 loose fit hole", "91.435 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M80-loose-max"
title = "M80 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M80", fit = "loose", tolerance = "max" }
aliases = ["M80 clearance hole loose", "M80 loose clearance hole", "M80 clearance hole", "ISO 273 M80 coarse", "M80 loose fit hole", "91.87 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M90-close-min"
title = "M90 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M90", fit = "close", tolerance = "min" }
aliases = ["M90 clearance hole close", "M90 close clearance hole", "M90 clearance hole", "ISO 273 M90 fine", "M90 close fit hole", "93 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M90-close-mean"
title = "M90 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M90", fit = "close", tolerance = "mean" }
aliases = ["M90 clearance hole close", "M90 close clearance hole", "M90 clearance hole", "ISO 273 M90 fine", "M90 close fit hole", "93.175 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M90-close-max"
title = "M90 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M90", fit = "close", tolerance = "max" }
aliases = ["M90 clearance hole close", "M90 close clearance hole", "M90 clearance hole", "ISO 273 M90 fine", "M90 close fit hole", "93.35 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M90-normal-min"
title = "M90 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M90", fit = "normal", tolerance = "min" }
aliases = ["M90 clearance hole normal", "M90 normal clearance hole", "M90 clearance hole", "ISO 273 M90 medium", "M90 normal fit hole", "96 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M90-normal-mean"
title = "M90 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M90", fit = "normal", tolerance = "mean" }
aliases = ["M90 clearance hole normal", "M90 normal clearance hole", "M90 clearance hole", "ISO 273 M90 medium", "M90 normal fit hole", "96.27 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M90-normal-max"
title = "M90 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M90", fit = "normal", tolerance = "max" }
aliases = ["M90 clearance hole normal", "M90 normal clearance hole", "M90 clearance hole", "ISO 273 M90 medium", "M90 normal fit hole", "96.54 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M90-loose-min"
title = "M90 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M90", fit = "loose", tolerance = "min" }
aliases = ["M90 clearance hole loose", "M90 loose clearance hole", "M90 clearance hole", "ISO 273 M90 coarse", "M90 loose fit hole", "101 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M90-loose-mean"
title = "M90 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M90", fit = "loose", tolerance = "mean" }
aliases = ["M90 clearance hole loose", "M90 loose clearance hole", "M90 clearance hole", "ISO 273 M90 coarse", "M90 loose fit hole", "101.435 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M90-loose-max"
title = "M90 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M90", fit = "loose", tolerance = "max" }
aliases = ["M90 clearance hole loose", "M90 loose clearance hole", "M90 clearance hole", "ISO 273 M90 coarse", "M90 loose fit hole", "101.87 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M100-close-min"
title = "M100 clearance hole, close (fine series), min of the tolerance"
params = { thread = "M100", fit = "close", tolerance = "min" }
aliases = ["M100 clearance hole close", "M100 close clearance hole", "M100 clearance hole", "ISO 273 M100 fine", "M100 close fit hole", "104 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M100-close-mean"
title = "M100 clearance hole, close (fine series), mean of the tolerance"
params = { thread = "M100", fit = "close", tolerance = "mean" }
aliases = ["M100 clearance hole close", "M100 close clearance hole", "M100 clearance hole", "ISO 273 M100 fine", "M100 close fit hole", "104.175 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M100-close-max"
title = "M100 clearance hole, close (fine series), max of the tolerance"
params = { thread = "M100", fit = "close", tolerance = "max" }
aliases = ["M100 clearance hole close", "M100 close clearance hole", "M100 clearance hole", "ISO 273 M100 fine", "M100 close fit hole", "104.35 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M100-normal-min"
title = "M100 clearance hole, normal (medium series), min of the tolerance"
params = { thread = "M100", fit = "normal", tolerance = "min" }
aliases = ["M100 clearance hole normal", "M100 normal clearance hole", "M100 clearance hole", "ISO 273 M100 medium", "M100 normal fit hole", "107 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M100-normal-mean"
title = "M100 clearance hole, normal (medium series), mean of the tolerance"
params = { thread = "M100", fit = "normal", tolerance = "mean" }
aliases = ["M100 clearance hole normal", "M100 normal clearance hole", "M100 clearance hole", "ISO 273 M100 medium", "M100 normal fit hole", "107.27 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M100-normal-max"
title = "M100 clearance hole, normal (medium series), max of the tolerance"
params = { thread = "M100", fit = "normal", tolerance = "max" }
aliases = ["M100 clearance hole normal", "M100 normal clearance hole", "M100 clearance hole", "ISO 273 M100 medium", "M100 normal fit hole", "107.54 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M100-loose-min"
title = "M100 clearance hole, loose (coarse series), min of the tolerance"
params = { thread = "M100", fit = "loose", tolerance = "min" }
aliases = ["M100 clearance hole loose", "M100 loose clearance hole", "M100 clearance hole", "ISO 273 M100 coarse", "M100 loose fit hole", "112 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M100-loose-mean"
title = "M100 clearance hole, loose (coarse series), mean of the tolerance"
params = { thread = "M100", fit = "loose", tolerance = "mean" }
aliases = ["M100 clearance hole loose", "M100 loose clearance hole", "M100 clearance hole", "ISO 273 M100 coarse", "M100 loose fit hole", "112.435 mm hole"]
standard = "ISO 273"

[[presets]]
id = "M100-loose-max"
title = "M100 clearance hole, loose (coarse series), max of the tolerance"
params = { thread = "M100", fit = "loose", tolerance = "max" }
aliases = ["M100 clearance hole loose", "M100 loose clearance hole", "M100 clearance hole", "ISO 273 M100 coarse", "M100 loose fit hole", "112.87 mm hole"]
standard = "ISO 273"